{"product_id":"ge-is200jpdcg1a-power-distribution-module","title":"GE IS200JPDCG1A Power Distribution Module","description":"\u003cp\u003e\u003cstrong\u003eGE IS200JPDCG1A Power Distribution Module\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eGE IS200JPDCG1A\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200JPDCG1A\u003c\/strong\u003e power distribution module, operates as a dedicated hardware component for distributing 125 VDC, 115\/230 VAC, and 28 VDC excitation rails within Mark VI \/ Mark VIe turbine‑control power frames.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHardware Specifications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eIS200JPDCG1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOrigin\u003c\/th\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOperating Temp\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower Consumption\u003c\/th\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduct Type\u003c\/th\u003e\n\u003ctd\u003ePower Distribution Module\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eMark VI \/ Mark VIe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eNominal Voltage\u003c\/th\u003e\n\u003ctd\u003e28 VDC (distribution), plus 125 VDC and 115\/230 VAC routing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMounting\u003c\/th\u003e\n\u003ctd\u003eMetal sub‑panel via standoffs and screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eConnectors\u003c\/th\u003e\n\u003ctd\u003eScrew terminals, stab‑on connectors, multi‑pin plug assemblies\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eToggle Switches\u003c\/th\u003e\n\u003ctd\u003e7 independent switches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTerminal Strips\u003c\/th\u003e\n\u003ctd\u003eOne 5‑position strip, three 3‑position auxiliary strips\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProtection\u003c\/th\u003e\n\u003ctd\u003eFuses, surge suppression, isolation networks\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSafety Delay\u003c\/th\u003e\n\u003ctd\u003e30‑second re‑energization wait requirement\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003cp\u003e\u003cstrong\u003eBackplane Bus Communication Velocity Licenses\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eJPDC aligns with GE’s deterministic backplane behavior used across Mark VI \/ Mark VIe power‑distribution assemblies. Although the board itself is passive, its routing of AC\/DC rails follows fixed sampling intervals defined by the PPDA pack. I\/O density scaling ensures that each downstream board receives identical excitation mapping, preventing uneven loading across redundant frames. Firmware flash compatibility resides at the PPDA level; JPDC provides fixed electrical behavior without programmable logic. Deterministic Profinet \/ EtherNet\/IP timing is preserved by maintaining stable excitation rails for I\/O packs that rely on synchronized power‑domain transitions.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequently Asked Questions\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eQ: Can IS200JPDCG1A be hot‑swapped? A: No. The 30‑second wait label indicates that internal capacitors must fully discharge before re‑energization.\u003c\/p\u003e\n\u003cp\u003eQ: Does JPDC introduce delay in diagnostic feedback? A: No. Diagnostic timing is governed by the PPDA I\/O pack; JPDC only routes signals.\u003c\/p\u003e\n\u003cp\u003eQ: Are the AC and DC domains isolated? A: Yes. Internal isolation networks prevent cross‑domain interaction between 125 VDC, 115\/230 VAC, and 28 VDC rails.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eField Installation Guidelines\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMount vertically on a rigid metal sub‑panel using all standoffs to prevent trace flexing.\u003c\/li\u003e\n\u003cli\u003ePosition AC input connector (JAC) at the bottom per GE cabinet layout conventions.\u003c\/li\u003e\n\u003cli\u003eMaintain segregation between high‑energy AC conductors and low‑voltage DC rails.\u003c\/li\u003e\n\u003cli\u003eUse correct stab‑on and screw‑terminal torque to avoid conductor fatigue.\u003c\/li\u003e\n\u003cli\u003eSecure the PPDA pack to JA1 using the angle bracket and threaded studs.\u003c\/li\u003e\n\u003cli\u003eRoute diagnostic ribbon cable to P2 with strain relief to prevent connector stress.\u003c\/li\u003e\n\u003cli\u003eObserve the 30‑second discharge delay before re‑applying power.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE","offers":[{"title":"Default Title","offer_id":43867997306954,"sku":"IS200JPDCG1A","price":6800.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0587\/8569\/3770\/files\/IS200JPDMG1ADC_2.png?v=1741760161","url":"https:\/\/www.topbrandsplc.com\/products\/ge-is200jpdcg1a-power-distribution-module","provider":"Topbrands PLC Limited","version":"1.0","type":"link"}